pix端口映射问题
原来公司网管设的xxx.xx.1.14：80端口可由网外访问，现在想让xxx.xx.1.14：8080端口也可能外网访问，我按原来的设置加了一条规则但还是不能从外网访问，以下是设置，哪位大侠帮忙看看，多谢了pixfirewall# sh run
: Saved
:
PIX Version 6.3(4)
interface ethernet0 auto
interface ethernet1 auto
interface ethernet2 auto
nameif ethernet0 outside security0
nameif ethernet1 inside security100
nameif ethernet2 dmz security50
enable password xxxxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxxxxxxx encrypted
hostname pixfirewall
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol ftp 8080
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol http 8080
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list 101 permit ip 172.16.0.0 255.255.0.0 192.168.1.0 255.255.255.0
pager lines 24
mtu outside 1500
mtu inside 1500
mtu dmz 1500
ip address outside xxx.xx.1.11 255.255.255.248
ip address inside 172.16.1.253 255.255.255.0
ip address dmz 192.168.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
no failover
failover timeout 0:00:00
failover poll 15
no failover ip address outside
no failover ip address inside
no failover ip address dmz
pdm history enable
arp timeout 14400
global (outside) 1 xxx.xx.1.12 netmask 255.255.255.248
nat (inside) 0 access-list 101
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
nat (dmz) 1 0.0.0.0 0.0.0.0 0 0
static (dmz,outside) xxx.xx.1.14 192.168.1.2 netmask 255.255.255.255 0 0
static (dmz,outside) xxx.xx.1.13 192.168.1.3 netmask 255.255.255.255 0 0
conduit permit icmp any any
conduit permit tcp host xxx.xx.1.14 eq www any
conduit permit tcp host xxx.xx.1.14 eq ftp any
conduit permit tcp host xxx.xx.1.14 eq smtp any
conduit permit tcp host xxx.xx.1.14 eq pop3 any
conduit permit tcp host xxx.xx.1.14 eq 3389 any
conduit permit tcp host xxx.xx.1.14 eq ftp-data any
conduit permit tcp host xxx.xx.1.13 eq ftp any
conduit permit tcp host xxx.xx.1.13 eq smtp any
conduit permit tcp host xxx.xx.1.13 eq pop3 any
conduit permit tcp host xxx.xx.1.13 eq www any
conduit deny tcp any any
conduit deny udp any any
conduit permit tcp host xxx.xx.1.14 eq 8080 any
outbound 10 deny 172.16.6.0 255.255.0.0 4000 tcp
outbound 10 deny 172.16.6.0 255.255.0.0 8000 tcp
outbound 10 deny 172.16.0.0 255.255.0.0 8000 udp
apply (inside) 10 outgoing_src
route outside 0.0.0.0 0.0.0.0 222.36.1.10 1
route inside 172.16.0.0 255.255.0.0 172.16.1.254 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet timeout 5
ssh timeout 5
console timeout 0
terminal width 80
Cryptochecksum: 顺序错了
conduit permit tcp host xxx.xx.1.14 eq 8080 any
要在
conduit deny tcp any any
conduit deny udp any any
这两句之前 弱弱的问，咋放到那两句之前啊？谢谢了。呵呵 备份下来，然后全部重写 我去试试，再次感谢 这是篇好文章，下载了看看！ 整不明白，有待学习！
页:
[1]
